当前位置:首页-新闻资讯

铝板使用中要注意什么?

来源:http://www.jndclyyxgs.com/ 发布时间:2023-05-15

1、铝板贮存:应将板材存放于干燥通风处,且平放在平整的表面上,切勿踩踏、撞击。
1. Aluminum plate storage: The plate should be stored in a dry and ventilated place, and placed flat on a flat surface, without stepping or hitting.
2、铝板搬运:搬运板材应将板的四边同时抬起,严禁推拉、抽取,以免刮伤板面。
2. Aluminum plate handling: When handling the plate, the four sides of the plate should be lifted simultaneously, and it is strictly prohibited to push, pull, or extract to avoid scratching the plate surface.
3、铝板开槽:用开槽机或锣机开槽时,应使用半圆头式大于90度的铣刀.下刀既不要过深伤及铝板,也不要过浅使折边困难,应留有0.2-0.3MM厚塑料芯材连同铝板一起弯边,以增加强度和韧性,否则在弯边时铝板可能断裂或漆膜爆裂。
3. Aluminum plate slotting: When using a slotting machine or gong machine for slotting, a milling cutter with a semicircular head greater than 90 degrees should be used. The lower cutter should not be too deep to damage the aluminum plate, nor too shallow to make it difficult to fold. A plastic core material with a thickness of 0.2-0.3MM should be left to bend along with the aluminum plate to increase strength and toughness, otherwise the aluminum plate may break or the paint film may burst during the bending process.
铝板生产厂家
4、铝板弯边:弯边时需用力均匀,一次成型,不要反复弯折,否则铝板可能断裂。
4. Aluminum plate bending: When bending, it is necessary to use even force and form it in one go. Do not bend it repeatedly, otherwise the aluminum plate may break.
5、铝板弧形加工:加工弧形应使用专用弯曲设备加工,徐徐用力,使板材逐步达到所需的曲面.切勿一次弯曲成型。
5. Aluminum plate arc processing: Special bending equipment should be used to process the arc, and gradual force should be applied to gradually achieve the required surface of the plate. Do not bend it into shape at once.
6、铝板批次:同一型号而不同批次的板材可能存在色差,出售和使用不同批次板材时应增加比对色差之程序,我们公司主要经营合金铝板、铝花纹板等,无视觉色差时方可在同一平面使用。
6. Aluminum plate batch: Different batches of plates of the same model may have color differences. When selling and using different batches of plates, a color difference comparison program should be added. Our company mainly operates alloy aluminum plates, aluminum patterned plates, etc. Only when there is no visual color difference can we use them on the same plane.
7、铝板安装方向:将同色铝板安装在同一平面时,流程方向应一致,否则可能造视觉色差。
7. Installation direction of aluminum plate: When installing the same color aluminum plate on the same plane, the process direction should be consistent, otherwise it may cause visual color difference.
8、铝板撕膜:应在铝板安装后的45天内撕去保护膜,否则可能发生撕膜困难或移胶现象。
8. Aluminum plate film tearing: The protective film should be removed within 45 days after the installation of the aluminum plate, otherwise difficulties in film tearing or adhesive removal may occur.
9、铝板使用条件:内墙板应在室内使用,不宜安装在室外,以保证使用效果和使用年限。
9. Aluminum panel usage conditions: The inner wall panel should be used indoors and should not be installed outdoors to ensure its effectiveness and lifespan.