当前位置:首页-新闻资讯

铝板使用过程中的九个注意事项

来源:http://www.jndclyyxgs.com/ 发布时间:2023-01-07

铝板在各行各业中使用非常广泛,它是一种很受欢迎的建筑装饰材料,在使用铝板时,肯定会遇到一些问题,下面铝板生产厂家就说一下铝板使用过程中的九个注意事项。
Aluminum plate is widely used in all walks of life. It is a very popular building decoration material. When using aluminum plate, there will certainly be some problems. The aluminum plate manufacturer will talk about nine precautions during the use of aluminum plate.
一、铝板贮存:应将板材存放于干燥通风处,且平放在平整的表面上,切勿踩踏、撞击。
1、 Storage of aluminum plates: The plates shall be stored in a dry and ventilated place, flat on a flat surface, and shall not be stepped on or struck.
二、铝板搬运:搬运板材应将板的四边同时抬起,严禁推拉、抽取,以免刮伤板面。
2、 Aluminum plate handling: when handling the plates, the four sides of the plates shall be lifted at the same time. It is strictly prohibited to push, pull or extract the plates to avoid scratching the surface.
三、铝板开槽:用开槽机或锣机开槽时,应使用半圆头式大于90度的铣刀.下刀既不要过深伤及铝板,也不要过浅使折边困难,应留有0.2-0.3MM厚塑料芯材连同铝板一起弯边,以增加强度和韧性,否则在弯边时铝板可能断裂或漆膜爆裂。
3、 Aluminum plate slotting: When slotting with a slotting machine or a gondola machine, a semicircle head milling cutter larger than 90 degrees should be used. The cutting tool should not be too deep to damage the aluminum plate, nor too shallow to make folding difficult. A 0.2-0.3MM thick plastic core should be left with the aluminum plate bent together to increase strength and toughness, otherwise the aluminum plate may break or the paint film burst when bending.
四、铝板弯边:弯边时需用力均匀,一次成型,不要反复弯折,否则铝板可能断裂。
4、 Aluminum plate bending: the bending force shall be uniform, forming at one time, do not bend repeatedly, or the aluminum plate may break.

铝板生产厂家
五、铝板弧形加工:加工弧形应使用专用弯曲设备加工,徐徐用力,使板材逐步达到所需的曲面.切勿一次弯曲成型。
5、 Arc processing of aluminum plate.
六、铝板批次:同一型号而不同批次的板材可能存在色差,出售和使用不同批次板材时应增加比对色差之程序,我们公司主要经营合金铝板、铝花纹板等,无视觉色差时方可在同一平面使用。
6、 Aluminum plate batch: The plates of the same model but different batches may have color difference. When selling and using different batches of plates, the procedure for comparing color difference should be added. Our company mainly deals in alloy aluminum plates, aluminum pattern plates, etc., and can only be used on the same plane when there is no visual color difference.
七、铝板安装方向:将同色铝板安装在同一平面时,流程方向应一致,否则可能造视觉色差。
7、 Aluminum plate installation direction: when installing aluminum plates with the same color on the same plane, the flow direction should be consistent, otherwise visual color difference may occur.
八、铝板撕膜:应在铝板安装后的45天内撕去保护膜,否则可能发生撕膜困难或移胶现象。
8、 Tearing film of aluminum plate: the protective film shall be removed within 45 days after the installation of aluminum plate, otherwise it may be difficult to tear the film or remove the adhesive.
九、铝板使用条件:内墙板应在室内使用,不宜安装在室外,以保证使用效果和使用年限。
9、 Service conditions of aluminum plate: the interior wallboard shall be used indoors rather than installed outdoors to ensure the service effect and service life.
此外由于铝板的不断地火热,在市场上出现了各种各样的铝板产品的,每个厂家都介绍自己品质好,的确让人难以选取,所以在购买的时候要多方面进行考虑。更多相关内容就来我们网站http://www.jndclyyxgs.com进行咨询吧!
In addition, due to the continuous popularity of aluminum plates, a variety of aluminum plate products have appeared in the market. Each manufacturer has introduced their good quality, which is really difficult to choose. Therefore, we should consider many aspects when purchasing. More relevant content will come to our website http://www.jndclyyxgs.com Consult!