铝板生产厂家

您的位置:首页 > 新闻资讯 >

环保材质的铝板使用应该提前做好了解

来源:http://www.jndclyyxgs.com  发布时间:2022-05-10 23:07:32  

铝板是一种优质的建筑材料,是一种比较环保的材料。广泛应用于工程装饰、家居装饰、通讯电子、交通设施、保温防腐、精装修、汽车制造等领域。使用中的知识点是什么?
Aluminum plate is a high-quality building material and a relatively environmentally friendly material. It is widely used in engineering decoration, home decoration, communication electronics, transportation facilities, thermal insulation and anti-corrosion, fine decoration, automobile manufacturing and other fields. What are the knowledge points in use?
铝板存放:应存放于干燥通风处,平放于表面,勿踩踏或撞击。铝板的搬运:铝板的四面要同时提起,以免划伤板面。
Aluminum plate storage: it should be stored in a dry and ventilated place and placed flat on the surface. Do not step on or hit it. Handling of aluminum plate: the four sides of the aluminum plate shall be lifted at the same time to avoid scratching the plate surface.
铝板开槽:用插床或锣机开槽时,应使用半圆端铣刀。不管对铝板的损伤是不是太深、不是太浅、不容易折,都要把0.2-0.3mm厚的胶芯和铝板一起折弯,以增加强度和韧性,否则铝板弯曲时可能会破裂或漆膜破裂。
Aluminum plate slotting: when slotting with slotting machine or gong machine, semi-circular end milling cutter shall be used. No matter whether the damage to the aluminum plate is too deep, not too shallow and not easy to fold, the rubber core with a thickness of 0.2-0.3mm shall be bent together with the aluminum plate to increase the strength and toughness, otherwise the aluminum plate may break or the paint film may break when it is bent.

铝板生产厂家
铝板批次:同类型不同批次的铝板可能存在色差。在销售和使用不同批次的纸张时,应增加色差比较程序。我公司主要经营合金铝板、铝花纹板等。只有在没有视觉色差的情况下才能在同一平面上使用。
Aluminum plate batch: different batches of aluminum plates of the same type may have color difference. Color difference comparison procedures should be added when selling and using different batches of paper. Our company is mainly engaged in aluminum alloy plate, aluminum pattern plate, etc. It can only be used on the same plane without visual color difference.
铝板安装方向:相同颜色的铝板安装在同一平面上时,流向应一致,否则会出现视觉色差。铝板撕膜:铝板安装后45天内撕掉保护膜,否则撕膜困难或出现胶转移。铝板使用条件:室内墙板应在室内使用,不得安装在室外,以保证使用效果和使用寿命。
Installation direction of aluminum plate: when aluminum plates of the same color are installed on the same plane, the flow direction shall be consistent, otherwise there will be visual color difference. Aluminum plate film tearing: tear off the protective film within 45 days after aluminum plate installation, otherwise it is difficult to tear the film or glue transfer occurs. Service conditions of aluminum plate: the indoor wall plate shall be used indoors and shall not be installed outdoors to ensure the service effect and service life.
铝板折弯:折边时受力均匀,一次成型,不要反复折弯,否则铝板可能会断裂。铝板圆弧加工:铝板生产厂家提醒大家,加工圆弧时要使用专用的折弯设备,使板材逐渐达到要求的表面,不能一次折弯。
Bending of aluminum plate: the force is uniform when folding. It is formed at one time. Do not bend repeatedly, otherwise the aluminum plate may break. Aluminum plate arc processing: aluminum plate manufacturers remind everyone that special bending equipment should be used when processing arc, so that the plate can gradually reach the required surface and can not be bent at one time.
相信通过上面内容的介绍,大家对铝板使用的知识点都有一定的了解了,如果您想要知道更多的有关内容点,可以关注我们的网站www.jndclyyxgs.com
I believe that through the introduction of the above contents, we have a certain understanding of the knowledge points of aluminum plate use. If you want to know more about the content points, you can pay attention to our website www.jndclyyxgs com。