当前位置:首页-新闻资讯

铝圆片的清洗工艺及除油方法

来源:http://www.jndclyyxgs.com/ 发布时间:2020-04-20

  1.为了减少数控刀片的滑动摩擦材料,需要使用一些乳化油,铝圆片生产加工,剩余的光滑油不能简单地擦去,这需要一个特殊的石油剂,泡沫油渗透的常见方法及其self-spraying石油。
  1. in order to reduce the sliding friction material of NC blade, it is necessary to use some emulsified oil and aluminum wafer to produce and process. The remaining smooth oil can not be simply erased. This requires a special petroleum agent, a common method of foam oil penetration and its self-spraying oil.
  2.自喷除油除灰:稀释剂除油剂和除灰剂分别加适量水;2. 调整喷头角度;3、确保铝合金型材工艺的自喷时间(多在30秒内);4. 确保铝晶圆通过循环系统手洗。
  2. Oil and ash removal by self spraying: add appropriate amount of water to the diluent oil remover and ash remover respectively; 2. Adjust the nozzle angle; 3. Ensure the self spraying time of aluminum alloy profile technology (more than 30 seconds); 4. Ensure that the aluminum wafer is washed by hand through the circulation system.
  1.使用前加少量饮用水,然后将铝片渗入池中;(良好的调灰剂);2、参与铝片脱脂,在5—10秒内自动加热;3.2~3分钟去油,用清水冲洗干净;4、成灰剂成灰(时间不跨越30秒左右);5. 清洁饮用水——晾干(日晒)或停止空气氧化。
  1. Add a small amount of drinking water before use, and then infiltrate the aluminum into the pool; (good ash mixing agent); 2. Participate in the degreasing of aluminum, and automatically heat it within 5-10 seconds; 3.2-3 minutes to remove oil, and wash it with clean water; 4. Ash forming agent and ash forming (the time does not exceed about 30 seconds); 5. Clean drinking water - air drying (sun drying) or stop air oxidation.
  铝圆片清洗工艺:
  Aluminum wafer cleaning process:
  1,用大量冷水清洗污垢的铝圆片外观,然后撒水稀释的清洁剂,用薄布,擦拭铝圆片的外观,然后有很多冷水清洗铝圆片的外观清洁后,铝圆片的外观脏东西冲了。
  1. First, clean the appearance of the dirty aluminum wafer with a large amount of cold water, then sprinkle water to dilute the detergent, wipe the appearance of the aluminum wafer with a thin cloth, and then clean the appearance of the aluminum wafer with a lot of cold water, and the appearance of the aluminum wafer is dirty.
  2、检查铝盘的外观,看是否有不干净的地方,约不干净的地方整理,知道全部清洁后,再用冷水洗去所有清洁剂。

铝板生产厂家
  2. Check the appearance of the aluminum plate to see if there is any unclean place. The unclean place should be cleaned first. After knowing all the cleaning, wash all the cleaning agents with cold water.
  3,除了注意不是安排铝盘的温度,由于水的蒸发过快将有害的外观油漆、洗涤剂的使用期间,必须选择中性洗涤剂或将侵蚀铝盘的外观。
  3. In addition to not arranging the temperature of the aluminum plate, the neutral detergent must be selected or will corrode the appearance of the aluminum plate during the use of the harmful appearance paint and detergent due to the rapid evaporation of water.
  以上是铝板生产厂家为大家介绍的相关内容,想要了解更多内容,欢迎访问网站:http://www.jndclyyxgs.com
  The above is the relevant content introduced by the aluminum plate manufacturer for you. To learn more, please visit the website: http://www.jndclyxgs.com